收藏本站
CS5463
5.16 Commands
All commands are 8 bits in length. Any command byte value that is not listed in this section is invalid. Commands
that write to registers must be followed by 3 bytes of data. Commands that read data can be chained with other com-
mands (e.g., while reading data, a new command can be sent which can execute during the original read). All com-
mands except register reads, register writes, and SYNC0 & SYNC1 will abort any currently executing commands.
5.16.1 Start Conversions
B7
1
B6
1
B5
1
B4
0
B3
C3
B2
0
B1
0
B0
0
Initiates acquiring measurements and calculating results. The device has two modes of acquisition.
C3
Modes of acquisition/measurement
0 = Perform a single computation cycle
1 = Perform continuous computation cycles
5.16.2 SYNC0 and SYNC1
B7
1
B6
1
B5
1
B4
1
B3
1
B2
1
B1
1
B0
SYNC
The serial port can be initialized by asserting CS or by sending three or more consecutive SYNC1 commands fol-
lowed by a SYNC0 command. The SYNC0 or SYNC1 can also be sent while sending data out.
SYNC
0 = Last byte of a serial port re-initialization sequence.
1 = Used during reads and serial port initialization.
5.16.3 Power-up/Halt
B7
1
B6
0
B5
1
B4
0
B3
0
B2
0
B1
0
B0
0
If the device is powered-down, Power-Up/Halt will initiate a power on reset. If the part is already powered-on, all
computations will be halted.
5.16.4 Power-down and Software Reset
B7
1
B6
0
B5
0
B4
S1
B3
S0
B2
0
B1
0
B0
0
To conserve power the CS5463 has two power-down states. In stand-by state all circuitry, except the analog/digital
clock generators, is turned off. In the sleep state all circuitry, except the command decoder, is turned off. Bringing
the CS5463 out of sleep state requires more time than out of stand-by state, because of the extra time needed to
re-start and re-stabilize the analog oscillator.
S[1:0]
DS678F3
Power-down state
00 = Software Reset
01 = Halt and enter stand-by power saving state. This state allows quick power-on
10 = Halt and enter sleep power saving state.
11 = Reserved
23
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
CS5464-IS IC PWR/ENERGY METER 3CH 28-SSOP
CS5466-ISZR IC ENERGY METERING 1PHASE 24SSOP
CS5466-IS IC ENERGY METERING 1PHASE 24SSOP
CS8312YN8 IC PREDRIVER IGBT IGNITION 8DIP
CX1006 SOCKET ADAPTER 40TSOP SUPERPRO5K
CYCLONEMAX CYCLONE MAX FLASH PROGRAM
D-1723-WH DRAWER SLIDING 16.56X6.31X19.18"
D072-0103 DEV KIT 7 NIMBLE SBC/FUSION7/BB
相关代理商/技术参数
CS5463-ISZ 功能描述:电流和电力监控器、调节器 Single Phase Power/Energy IC RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel
CS5463-ISZ/D 制造商:Cirrus Logic 功能描述:
CS5463-ISZR 功能描述:电流和电力监控器、调节器 IC Single Phase PWR/Energy RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel
CS5463-ISZR/E2 制造商:Cirrus Logic 功能描述:
CS5464 制造商:CIRRUS 制造商全称:Cirrus Logic 功能描述:Three-channel, Single-phase Power/Energy IC
CS5464_07 制造商:CIRRUS 制造商全称:Cirrus Logic 功能描述:Three-channel, Single-phase Power/Energy IC
CS5464_11 制造商:CIRRUS 制造商全称:Cirrus Logic 功能描述:Three-channel, Single-phase Power/Energy IC
CS5464-IS 功能描述:电流和电力监控器、调节器 3-Ch Single Phase Power/Energy IC RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel